Quick Answer: How to Clean an Ice Maker
To clean your ice maker, remove any remaining ice and water, wash removable accessories, and wipe accessible interior surfaces. Then, follow your model's instructions for descaling or cleaning the internal water system. Rinse thoroughly, drain completely, and refill with fresh drinking water before making ice.
Important: Always check your model's manual before using a cleaning solution or running a cleaning cycle.
✅ What You Need
Before you start, prepare:
- Clean drinking water
- A soft cloth or soft brush
- Mild dish soap for removable parts
- An ice maker cleaning solution or descaler
For descaling, we recommend Silonn Ice Maker Cleaner, made with 100% pure food-contact citric acid. The pre-measured powder is easy to dissolve and is designed for removing hard water deposits and mineral scale.
| Product | Key Benefits | Buy Now |
|---|---|---|
|
|
100% pure food-contact citric acid; pre-measured pouches; easy to dissolve; no strong vinegar smell. Helps remove mineral buildup and limescale. | Shop Now |
💧 How to Clean Your Ice Maker
🔌 Step 1: Turn Off and Empty the Ice Maker
Turn off the machine and unplug it if you are cleaning removable or accessible parts manually.
Remove all ice from the basket and drain any remaining water from the reservoir.
🧽 Step 2: Clean the Ice Basket and Scoop
Take out the ice basket, scoop, and any other removable parts.
Wash them with warm water and mild dish soap, then rinse thoroughly and allow them to dry.
🧪 Step 3: Prepare the Cleaning Solution
Mix your ice maker cleaner according to the product instructions.
For Silonn Ice Maker Cleaner, mix one 1-ounce pouch with approximately 0.4 gallons of water.
Because it uses citric acid, the solution helps break down mineral deposits and limescale without leaving a strong vinegar smell.
💧 Step 4: Add the Cleaner to the Reservoir
Pour the prepared cleaning solution into the water reservoir.
Do not exceed the machine's maximum fill line.
🔄 Step 5: Run the Cleaning Cycle

Follow your ice maker manufacturer's instructions to run the cleaning solution through the machine. This helps the citric acid solution circulate through the internal water system and dissolve mineral buildup in hard-to-reach areas.
✨ Step 6: Wipe Away Remaining Buildup
After the cleaning cycle, use a soft cloth or soft-bristled brush to clean any visible residue inside the reservoir or other accessible areas.
Avoid abrasive pads or sharp tools that could damage the interior.
🚰 Step 7: Drain the Cleaning Solution

Drain all of the used cleaning solution from the machine.
Do not make drinking ice yet.
💧 Step 8: Rinse 2–3 Times

Refill the water reservoir with fresh, clean water. Turn on the ice maker and repeat the cleaning process 2–3 times using only fresh water to thoroughly flush out any remaining cleaning solution and loosened mineral deposits.
Drain the water completely after each rinse.
🧊 Step 9: Refill and Make Fresh Ice
Once the machine has been fully rinsed, reinstall the clean ice basket and refill the reservoir with fresh drinking water.
Your ice maker is now ready to use again.
🍋 Why Use Citric Acid Instead of Vinegar?
Vinegar is commonly used for descaling, but its strong smell can remain inside an ice maker and may require several rinse cycles.
Citric acid is a practical alternative because it:
- Helps dissolve hard water deposits and mineral scale
- Has little to no strong odor
- Dissolves easily in water
- Is convenient for regular ice maker maintenance
A pre-measured cleaner also removes the guesswork from mixing your own solution.
⭐ Recommended Ice Maker Cleaner
For a simple cleaning routine, Silonn Ice Maker Cleaner is a good option for countertop ice makers.
It uses 100% pure food-contact citric acid and comes in pre-portioned pouches, making it easy to prepare the right amount of cleaning solution each time.
Use it regularly—especially if you notice white mineral residue, cloudy ice, unusual taste, or slower ice production—to help keep mineral buildup under control.
💧 How Often Should You Clean an Ice Maker?
How often your ice maker needs descaling depends on your local water hardness, how frequently you use the machine, and how quickly mineral buildup develops.
Hard water contains more dissolved minerals, which can cause limescale to accumulate faster inside your ice maker.
Find Your Recommended Descaling Schedule
Step 1: Check Your Local Water Hardness
Find your state on the U.S. water hardness map below and check its estimated mineral concentration (mg/L). This gives you a starting point for understanding whether your local water is relatively hard or soft.

The map is for reference only. Actual household water hardness may vary by city, water source, and filtration system. Suggested intervals are general examples, not universal manufacturer requirements. Always follow your ice maker's manual and adjust descaling frequency based on how quickly mineral buildup develops.
Step 2: Consider How Often You Use Your Ice Maker
- Occasional use: 1–2 days per week
- Regular use: 3–5 days per week
- Daily use: Every day
The more frequently you make ice, the more important it is to monitor your machine for mineral buildup.
Step 3: Set Your Descaling Schedule
Use your model's recommended cleaning schedule as the starting point. Adjust the frequency based on your actual water hardness, usage, and visible scale.
If your area has hard water or you make ice every day, inspect your machine more frequently and descale when recommended by its manual.
Example: How to Determine Your Cleaning Frequency
Let's say you live in a region where your household water hardness is approximately 200 mg/L, and you use your ice maker 4–5 days per week.
- Location: A region with relatively hard water
- Water hardness: Approximately 200 mg/L
- Usage: Regular use, 4–5 days per week
- Example descaling interval: Every 2 weeks, if permitted by your model's maintenance instructions
Start with that interval, monitor mineral buildup, and adjust as needed.
Remember: Routine cleaning and descaling are different. Continue cleaning removable parts and accessible surfaces according to your model's manual, even when mineral scale is not visible.
❓ Frequently Asked Questions
1. Does the Self-Cleaning Function Replace Manual Cleaning?
Not entirely. A self-cleaning cycle helps circulate water through the internal water system, but removable accessories and accessible surfaces may still need manual cleaning. Always follow your ice maker's user manual for the complete cleaning procedure.
2. How Do I Know If My Ice Maker Needs Descaling or Deep Cleaning?
Different types of buildup may require different cleaning methods:
- White, chalky deposits: Usually mineral scale that can be removed using a compatible descaling solution.
- Unusual odors or visible residue: Clean accessible surfaces and thoroughly rinse the water system.
- Black spots, slimy residue, or suspected mold: Follow your manufacturer's cleaning and sanitizing instructions. Contact customer support if the problem persists.
Remember: Descaling removes mineral deposits but does not necessarily sanitize your ice maker.
3. Can I Use Vinegar to Clean My Ice Maker?
Some ice maker manufacturers recommend diluted vinegar for specific models. Citric acid is another common descaling ingredient with less noticeable odor. Always check your model's instructions before choosing a cleaning solution.
4. Can I Use Citric Acid in Any Countertop Ice Maker?
Not necessarily. Cleaning solution compatibility and recommended concentrations vary by model. Always check your ice maker's manual and the cleaner's instructions before use.
5. Why Does My Ice Maker Still Smell After Cleaning?
Residual cleaning solution, old water, or buildup in accessible areas may cause unwanted odors. Rinse thoroughly according to your model's instructions. If the odor persists, stop using the machine and contact customer support.
6. What Should I Do If I'm Not Using My Ice Maker for a While?
Drain any remaining water, clean removable parts, and allow the interior to dry thoroughly before storage. Follow your model's storage instructions.
Silonn Ice Maker Cleaner